Are you facing challenges in the TP-Link Router login?
Well, you may not have to worry at all. With a proper guide and a bit of knowledge configuration of your TP-Link Router may not be a bigger challenge anymore. Almost everyone must know about how to set up your router in a flash. TP-Link Router follows the same procedures as most other models. You can simply go to your router settings page and follow up with the steps mentioned below to know about TP-Link Router login details.
TP-LINK Router Default IP
Note: Normally TP-Link Router’s default IP address is http://192.168.0.1 or http://192.168.1.1 (source)
How To Log in into My Router TP-Link?
Step 1: To log in to your TP-Link router, the first thing that you need to do is to get connected with your router. Turn on your router and wait for all LED lights to turn up. Once it shows up, look for available networks from your PC.
Step 2: Tap on your router name as mentioned on the label on your router. Tap on the network SSID as available and then enter your password. This is your default password which is also present in the label.
Step 3: Once done, you will now have to open up any web browser from your PC. Check your address bar and simply type down your IP address(find your router’s IP address) over here. This will lead you to the TP-Link login page. If you purchase a TP-Link cable router, enter http://tplinkmodem.net in the address bar of the browser.
Step 4: To enter your admin control panel you will have to enter your admin username and password. Usually, the default username and password are the same. Enter your username as ‘admin‘ followed by the password as ‘admin‘. Click on login to enter your control panel.
The default username and password are both ‘admin‘ for most of the TP-Link Router
💡 Note: You may forget your IP configuration and details after you log in for the first time. It is better to take a picture or a screenshot of your configuration details as this will help you to remember everything.
Change The TP-Link Router Login Password
Getting access to your TP-Link Router Login admin Panel is not the only thing that you need. To get your account secured, you will have to enter your login credentials and change them to make it more secure. This will help you to secure your data and network settings.
Step 1: Connect to your TP-Link Router and then option up your login page. You can simply type down the default username and password to log in. Tap on the login option and this will redirect you to the control panel.
Step 2: To change the settings from your control panel, you will have to go to your network settings. This should be available on the left side of your web page. Tap on this and then click on wireless.
Step 3: You will find a number of options available here. Simply tap on the wireless security option and then you will have to go to WPA/WPA2 mode. This will allow you to change your username and password.
Step 4: Find the menu where it is named as SSID configuration. Tap on this and then you will see your default username. Clear it out and enter a new SSID as per your choice. Once done, click on save changes to activate this.
Step 5: You can now go to password settings and then change your password. Enter your default password and then you can enter your new password. Enter this password again to confirm this. Click on save again to change this password.
Step 6: You can now go to reboot your router. Simply turn it off and wait for a few minutes before turning it on again. Unless you restart your router again, you won’t be able to update these changes. Wait for a few minutes and connect back to your router again.
💡 Note: While adding a new password for your TP-Link Router, make sure that the password is strong. You will have to ensure that you use a combination of special characters and alphanumeric codes which will help you to keep your network secure.
How To Find TP-Link Wi-Fi Password?
There are generally different ways by which you can quickly get your password. Even if you forget your password, you can quickly use them to enter back into your admin panel at any time.
Look for the label on your router. Every router from TP-Link comes with a label on top or bottom of this. This is your default username and password available over here. You can enter this to connect with your TP-Link router.
Another certain way to log into your admin panel is by going to find your credentials from Google. Simply type down your router serial number and you will be able to find your default username and password. You can enter them and log into your account easily.
If none of these options do work for you, another way out is to opt for a system check from the configuration. You can go to wireless settings and then go to the WPA2 security page. Here you will find your details about the new password or changed password. Take a picture of this and you will be able to access your admin panel through this.
Why Can’t I Log into My TP-Link Router?
There may be several reasons why you can’t log in to your TP-Link router. Probably the most common reason for them is that you have a crashed domain or IP configuration is not working properly. You can alter the settings by going to your admin login page and figure out the problem again. If this does not work, try resetting the router. Keep in mind that resetting the router will bring back all default settings. No new password and SSID will be active now. So to log in again you will have to enter your default SSID and password. There should be a small reset button available just behind your router. Simply tap on this for at least 10 seconds. Keep your hands off and you will be able to configure it properly.
Conclusion
You might face multiple technical difficulties while accessing your TP-Link router login. However, the easiest solution for all of them will be to get to restart your router easily. Resetting your router back to default settings will allow you to quickly configure. However, you must keep in mind that changing your network settings to private mode will only help you to keep it secure. When a router is configured for the first time, it is generally set in public mode. You will simply have to change it to a private network.